Advanced Guide: comptia n10 006

Master the comptia n10 006 CompTIA Network+ content and be ready for exam day success quickly with this Actualtests comptia n10 006 exam cost. We guarantee it!We make it a reality and give you real n10 006 practice test questions in our CompTIA n10 006 dump braindumps.Latest 100% VALID CompTIA n10 006 vce Exam Questions Dumps at below page. You can use our CompTIA n10 006 simulation questions braindumps and pass your exam.

2017 NEW RECOMMEND

Free VCE & PDF File for CompTIA N10-006 Real Exam
(Full Version!)

Pass on Your First TRY 100% Money Back Guarantee Realistic Practice Exam Questions

Free Instant Download NEW N10-006 Exam Dumps (PDF & VCE):
Available on:
http://www.certleader.com/N10-006-dumps.html

Q51. A network technician is performing a tracert command to troubleshoot a website-related issue. The following output is received for each hop in the tracert: 1 * * * Request timed out. 

2 * * * Request timed out. 

3 * * * Request timed out. 

The technician would like to see the results of the tracert command. Which of the following will allow the technician to perform tracert on external sites but not allow outsiders to discover information from inside the network? 

A. Enable split horizon to allow internal tracert commands to pass through the firewall 

B. Enable IGMP messages out and block IGMP messages into the network 

C. Configure the firewall to allow echo reply in and echo request out of the network 

D. Install a backdoor to access the router to allow tracert messages to pass through 

Answer:

Q52. A network technician is attempting to connect a new host to existing manufacturing equipment on an Ethernet network. The technician is having issues trying to establish communication between the old equipment and the new host. The technician checks the cabling for breaks and finds that the CAT3 cable in use is in perfect condition. Which of the following should the technician check to ensure the new host will connect? 

A. Confirm the new host is using 10GBaseSR due to the manufacturing environment 

B. Confirm the new host is compatible with 10BaseT Ethernet 

C. Confirm the existing 10Base2 equipment is using the proper frame type 

D. Confirm that CSMA/CD is disabled on the Ethernet network 

Answer:

Q53. Company policies require that all network infrastructure devices send system level information to a centralized server. Which of the following should be implemented to ensure the network administrator can review device error information from one central location? 

A. TACACS+ server 

B. Single sign-on 

C. SYSLOG server 

D. Wi-Fi analyzer 

Answer:

Q54. The administrator's network has OSPF for the internal routing protocol. One port going out to the Internet is congested. The data is going out to the Internet, but queues up before sending. Which of the following would resolve this issue? 

Output: 

Fast Ethernet 0 is up, line protocol is up 

Int ip address is 10.20.130.5/25 

MTU 1500 bytes, BW10000 kbit, DLY 100 usec 

Reliability 255/255, Tx load 1/255, Rx load 1/255 

Encapsulation ospf, loopback not set Keep alive 10 

Half duplex, 100Mb/s, 100 Base Tx/Fx 

Received 1052993 broadcasts 

0 input errors 

983881 packets output, 768588 bytes 

0 output errors, 0 collisions, 0 resets 

A. Set the loopback address 

B. Change the IP address 

C. Change the slash notation 

D. Change duplex to full 

Answer:

Q55. A technician is setting up a new network and wants to create redundant paths through the network. Which of the following should be implemented to prevent performance degradation? 

A. Port mirroring 

B. Spanning tree 

C. ARP inspection 

D. VLAN 

Answer:

Q56. Which of the following describes an area containing a rack that is used to connect customer equipment to a service provider? 

A. 110 block 

B. MDF 

C. DSU 

D. CSU 

Answer:

Q57. The management team wants to set up a wireless network in their office but all of their phones operate at the 2.4 GHz frequency. They need a wireless network that would be able to operate at a higher frequency than their phones. Which of following standards should be used? 

A. 802.11a 

B. 802.11b 

C. 802.11g 

D. 802.1x 

Answer:

Q58. A technician is tasked with connecting a router to a DWDM. The technician connects the router to the multiplexer and confirms that there is a good signal level. However, the interface on the router will not come up. Which of the following is the MOST likely cause? 

A. The wrong wavelength was demuxed from the multiplexer. 

B. The SFP in the multiplexer is malfunctioning. 

C. There is a dirty connector on the fiber optic cable. 

D. The fiber optic cable is bent in the management tray. 

Answer:

Q59. A service provider is unable to maintain connectivity to several remote sites at predetermined speeds. The service provider could be in violation of the: 

A. MLA. 

B. SLA. 

C. SOW. 

D. MOU. 

Answer:

Q60. A desktop computer is connected to the network and receives an APIPA address but is unable to reach the VLAN gateway of 10.10.100.254. Other PCs in the VLAN subnet are able to reach the Internet. Which of the following is MOST likely the source of the problem? 

A. 802.1q is not configured on the switch port 

B. APIPA has been misconfigured on the VLAN 

C. Bad SFP in the PC's 10/100 NIC 

D. OS updates have not been installed 

Answer:

Certleader Dumps
Certleader is a company specialized on providing high quality IT exam materials and fully committed to assist our respected clients crack any IT certification tests on their 1st efforts.