Facts about ccnp route 300 101 dumps pdf

Proper study guides for Up to the immediate present Cisco Implementing Cisco IP Routing certified begins with Cisco cisco 300 101 preparation products which designed to deliver the Practical 9tut ccnp 300 101 questions by making you pass the ccnp route 300 101 pdf test at your first time. Try the free route 300 101 demo right now.

2017 NEW RECOMMEND

Free VCE & PDF File for Cisco 300-101 Real Exam
(Full Version!)

Pass on Your First TRY 100% Money Back Guarantee Realistic Practice Exam Questions

Free Instant Download NEW 300-101 Exam Dumps (PDF & VCE):
Available on:
http://www.certleader.com/300-101-dumps.html

Q31. Which traffic characteristic is the reason that UDP traffic that carries voice and video is assigned to the queue only on a link that is at least 768 kbps? 

A. typically is not fragmented 

B. typically is fragmented 

C. causes windowing 

D. causes excessive delays for video traffic 

Answer:

Explanation: 

Q32. Which three characteristics are shared by subinterfaces and associated EVNs? (Choose three.) 

A. IP address 

B. routing table 

C. forwarding table 

D. access control lists 

E. NetFlow configuration 

Answer: A,B,C 

Explanation: 

A trunk interface can carry traffic for multiple EVNs. To simplify the configuration process, all

the subinterfaces and associated EVNs have the same IP address assigned. In other words, the trunk

interface is identified by the same IP address in different EVN contexts. This is accomplished as a result of

each EVN having a unique routing and forwarding table, thereby enabling support for overlapping IP

addresses across multiple EVNs. Reference: http://www.cisco.com/en/US/docs/ios-xml/ios/evn/

configuration/xe-3sg/evn- overview.pdf

Q33. Scenario: 

You have been asked to evaluate an OSPF network setup in a test lab and to answer questions a customer has about its operation. The customer has disabled your access to the show running-config command. 

How many times was SPF algorithm executed on R4 for Area 1? 

A. 1 

B. 5 

C. 9 

D. 20 

E. 54 

F. 224 

Answer:

Explanation: 

Q34. A network engineer has left a NetFlow capture enabled over the weekend to gather information regarding excessive bandwidth utilization. The following command is entered: 

switch#show flow exporter Flow_Exporter-1 What is the expected output? 

A. configuration of the specified flow exporter 

B. current status of the specified flow exporter 

C. status and statistics of the specified flow monitor 

D. configuration of the specified flow monitor 

Answer:

Explanation: 

show flow exporter exporter-name (Optional) Displays the current status of the specified flow exporter.

Example:

Device# show flow exporter

FLOW_EXPORTER-1

Reference: http://www.cisco.com/en/US/docs/ios-xml/ios/fnetflow/configuration/15-mt/cfg-de- fnflowexprts.

html

Q35. Refer to the exhibit. Which statement about the command output is true? 

A. The router exports flow information to 10.10.10.1 on UDP port 5127. 

B. The router receives flow information from 10.10.10.2 on UDP port 5127. 

C. The router exports flow information to 10.10.10.1 on TCP port 5127. 

D. The router receives flow information from 10.10.10.2 on TCP port 5127. 

Answer:

Explanation: 

Q36. You have been asked to evaluate how EIGRP is functioning in a customer network. 

What percent of R1’s interfaces bandwidth is EIGRP allowed to use? 

A. 10 

B. 20 

C. 30 

D. 40 

Answer:

Explanation: 

Q37. A network engineer executes the show crypto ipsec sa command. Which three pieces of information are displayed in the output? (Choose three.) 

A. inbound crypto map 

B. remaining key lifetime 

C. path MTU 

D. tagged packets 

E. untagged packets 

F. invalid identity packets 

Answer: A,B,C 

Explanation: 

show crypto ipsec sa This command shows IPsec SAs built between peers. The encrypted

tunnel is built between 12.1.1.1 and 12.1.1.2 for traffic that goes between networks 20.1.1.0 and 10.1.1.0.

You can see the two Encapsulating Security Payload (ESP) SAs built inbound and outbound.

Authentication Header (AH) is not used since there are

no AH SAs.

This output shows an example of the show crypto ipsec sa command (bolded ones found in answers for

this question).

interface: FastEthernet0

Crypto map tag: test, local addr. 12.1.1.1

local ident (addr/mask/prot/port): (20.1.1.0/255.255.255.0/0/0) remote ident (addr/mask/prot/port):

(10.1.1.0/255.255.255.0/0/0) current_peer: 12.1.1.2

PERMIT, flags={origin_is_acl,}

#pkts encaps: 7767918, #pkts encrypt: 7767918, #pkts digest 7767918 #pkts decaps: 7760382, #pkts

decrypt: 7760382, #pkts verify 7760382 #pkts compressed:

0, #pkts decompressed: 0

#pkts not compressed: 0, #pkts compr. failed: 0,

#pkts decompress failed: 0, #send errors 1, #recv errors 0 local crypto endpt.: 12.1.1.1, remote crypto

endpt.: 12.1.1.2 path mtu 1500, media mtu 1500

current outbound spi: 3D3

inbound esp sas:

spi: 0x136A010F(325714191)

transform: esp-3des esp-md5-hmac ,

in use settings ={Tunnel, }

slot: 0, conn id: 3442, flow_id: 1443, crypto map: test sa timing: remaining key lifetime (k/sec):

(4608000/52) IV size: 8 bytes

replay detection support: Y

inbound ah sas:

inbound pcp sas:

inbound pcp sas:

outbound esp sas:

spi: 0x3D3(979)

transform: esp-3des esp-md5-hmac ,

in use settings ={Tunnel, }

slot: 0, conn id: 3443, flow_id: 1444, crypto map: test sa timing: remaining key lifetime (k/sec):

(4608000/52) IV size: 8 bytes

replay detection support: Y

outbound ah sas:

outbound pcp sas:

Reference: http://www.cisco.com/c/en/us/support/docs/security-vpn/ipsec-negotiation-ike- protocols/5409-

ipsec-debug-00.html

Q38. Refer to the following command: router(config)# ip http secure-port 4433 

Which statement is true? 

A. The router will listen on port 4433 for HTTPS traffic. 

B. The router will listen on port 4433 for HTTP traffic. 

C. The router will never accept any HTTP and HTTPS traffic. 

D. The router will listen to HTTP and HTTP traffic on port 4433. 

Answer:

Explanation: 

To set the secure HTTP (HTTPS) server port number for listening, use the ip http secure-port

command in global configuration mode. To return the HTTPS server port number to the default, use the no

form of this command. ip http secure-port port-number no ip http secure-port Syntax Description port-

Integer in the range of 0 to 65535 is accepted, but the port number must be number higher than 1024

unless the default is used. The default is 443. Reference: http://www.cisco.com/en/US/docs/ios-xml/ios/

https/command/nm-https-cr-cl- sh.html#wp3612805529

Q39. You have been asked to evaluate how EIGRP is functioning in a customer network. 

What is the advertised distance for the 192.168.46.0 network on R1? 

A. 333056 

B. 1938688 

C. 1810944 

D. 307456 

Answer:

Explanation: 

Q40. An engineer executes the ip flow ingress command in interface configuration mode. What is the result of this action? 

A. It enables the collection of IP flow samples arriving to the interface. 

B. It enables the collection of IP flow samples leaving the interface. 

C. It enables IP flow while disabling IP CEF on the interface. 

D. It enables IP flow collection on the physical interface and its subinterfaces. 

Answer:

Explanation: 

Certleader Dumps
Certleader is a company specialized on providing high quality IT exam materials and fully committed to assist our respected clients crack any IT certification tests on their 1st efforts.