Ideas to ccna 200 125 book

we provide Practical Cisco ccna 200 125 torrent exam prep which are the best for clearing ccna 200 125 book test, and to get certified by Cisco CCNA Cisco Certified Network Associate CCNA (v3.0). The ccna 200 125 dumps Questions & Answers covers all the knowledge points of the real cisco 200 125 exam. Crack your Cisco ccna 200 125 syllabus Exam with latest dumps, guaranteed!

2017 NEW RECOMMEND

Free VCE & PDF File for Cisco 200-125 Real Exam
(Full Version!)

Pass on Your First TRY 100% Money Back Guarantee Realistic Practice Exam Questions

Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on:
http://www.certleader.com/200-125-dumps.html

Q161.  – (Topic 5)

Which two statements about static NAT translations are true? (Choose two.)

A. They allow connections to be initiated from the outside.

B. They require no inside or outside interface markings because addresses are statically defined.

C. They are always present in the NAT table.

D. They can be configured with access lists, to allow two or more connections to be initiated from the outside.

Answer: A,C

Explanation:

Static NAT is to map a single outside IP address to a single inside IP address. This is typically done to allow incoming connections from the outside (Internet) to the inside. Since these are static, they are always present in the NAT table even if they are not actively in use.

Q162.  – (Topic 5)

Refer to the exhibit.

Which rule does the DHCP server use when there is an IP address conflict?

A. The address is removed from the pool until the conflict is resolved.

B. The address remains in the pool until the conflict is resolved.

C. Only the IP detected by Gratuitous ARP is removed from the pool.

D. Only the IP detected by Ping is removed from the pool.

E. The IP will be shown, even after the conflict is resolved.

Answer: A

Explanation:

An address conflict occurs when two hosts use the same IP address. During address assignment, DHCP checks for conflicts using ping and gratuitous ARP. If a conflict is detected, the address is removed from the pool. The address will not be assigned until the administrator resolves the conflict.

(Reference: http://www.cisco.com/en/US/docs/ios/12_1/iproute/configuration/guide/1cddhcp.html)

Q163.  – (Topic 3)

What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?

A. 2

B. 8

C. 16

D. unlimited

Answer: B

Explanation:

maximum-paths (OSPF)

To control the maximum number of parallel routes that Open Shortest Path First (OSPF) can support, use the maximum-paths command.

Syntax Description

maximum

Maximum number of parallel routes that OSPF can install in a routing table. The range is from 1 to 16 routes.

Command Default

8 paths

Q164.  – (Topic 4)

Which command allows you to verify the encapsulation type (CISCO or IETF) for a Frame Relay link?

A. show frame-relay lmi

B. show frame-relay map

C. show frame-relay pvc

D. show interfaces serial

Answer: B

Explanation:

When connecting Cisco devices with non-Cisco devices, you must use IETF4 encapsulation on both devices. Check the encapsulation type on the Cisco device with the show frame-relay map exec command.

Q165.  – (Topic 5)

Which two are features of IPv6? (Choose two.)

A. anycast

B. broadcast

C. multicast

D. podcast

E. allcast

Answer: A,C

Explanation:

IPv6 addresses are classified by the primary addressing and routing methodologies common in networking: unicast addressing, anycast addressing, and multicast addressing.

✑ A unicast address identifies a single network interface. The Internet Protocol

delivers packets sent to a unicast address to that specific interface.

✑ An anycast address is assigned to a group of interfaces, usually belonging to different nodes. A packet sent to an anycast address is delivered to just one of the member interfaces, typically the nearest host, according to the routing protocol’s definition of distance. Anycast addresses cannot be identified easily, they have the same format as unicast addresses, and differ only by their presence in the network at multiple points. Almost any unicast address can be employed as an anycast address.

✑ A multicast address is also used by multiple hosts, which acquire the multicast address destination by participating in the multicast distribution protocol among the network routers. A packet that is sent to a multicast address is delivered to all interfaces that have joined the corresponding multicast group.

Q166.  – (Topic 8)

Refer to the exhibit.

While troubleshooting a switch, you executed the show interface port-channel 1 etherchannel command and it returned this output. Which information is provided by the Load value?

A. the percentage of use of the link

B. the preference of the link

C. the session count of the link

D. the number source-destination pairs on the link

Answer: D

Q167.  – (Topic 8)

Which configuration can you apply to enable encapsulation on a subinterface?

A. interface FastEthernet 0/0 encapsulation dot1Q 30

ip address 10.1.1.30 255.255.255.0

B. interface FastEthernet 0/0.30

ip address 10.1.1.30 255.255.255.0

C. interface FastEthernet 0/0.30 description subinterface vlan 30

D. interface FastEthernet 0/0.30 encapsulation dot1Q 30

ip address 10.1.1.30 255.255.255.0

Answer: D

Q168.  – (Topic 5)

Which IPv6 address is the all-router multicast group?

A. FF02::1

B. FF02::2

C. FF02::3

D. FF02::4

Answer: B

Explanation:

Well-known IPv6 multicast addresses:

Address Description ff02::1

All nodes on the local network segment

ff02::2

All routers on the local network segment

Certleader Dumps
Certleader is a company specialized on providing high quality IT exam materials and fully committed to assist our respected clients crack any IT certification tests on their 1st efforts.