Secrets to ccna 210 260

Want to know Examcollection ccna security 210 260 official cert guide pdf Exam practice test features? Want to lear more about Cisco Implementing Cisco Network Security certification experience? Study Real Cisco ccna security 210 260 answers to Replace 210 260 vce questions at Examcollection. Gat a success with an absolute guarantee to pass Cisco ccna security 210 260 official cert guide pdf (Implementing Cisco Network Security) test on your first attempt.


Free VCE & PDF File for Cisco 210-260 Real Exam
(Full Version!)

Pass on Your First TRY 100% Money Back Guarantee Realistic Practice Exam Questions

Free Instant Download NEW 210-260 Exam Dumps (PDF & VCE):
Available on:

Q31. Which two features do CoPP and CPPr use to protect the control plane? (Choose two.) 

A. QoS 

B. traffic classification 

C. access lists 

D. policy maps 

E. class maps 

F. Cisco Express Forwarding 

Answer: A,B 

Q32. Which FirePOWER preprocessor engine is used to prevent SYN attacks? 

A. Rate-Based Prevention 

B. Portscan Detection 

C. IP Defragmentation 

D. Inline Normalization 


Q33. Refer to the exhibit. 

While troubleshooting site-to-site VPN, you issued the show crypto isakmp sa command. What does the given output show? 

A. IPSec Phase 1 is established between and 

B. IPSec Phase 2 is established between and 

C. IPSec Phase 1 is down due to a QM_IDLE state. 

D. IPSec Phase 2 is down due to a QM_IDLE state. 


Q34. What is one requirement for locking a wired or wireless device from ISE? Cisco 210-260 : Practice Test 

A. The ISE agent must be installed on the device. 

B. The device must be connected to the network when the lock command is executed. 

C. The user must approve the locking action. 

D. The organization must implement an acceptable use policy allowing device locking. 


Q35. Refer to the exhibit. 

Which statement about the device time is true? 

A. The time is authoritative, but the NTP process has lost contact with its servers. 

B. The time is authoritative because the clock is in sync. 

C. The clock is out of sync. 

D. NTP is configured incorrectly. 

E. The time is not authoritative. 


Q36. What command can you use to verify the binding table status? 

A. show ip dhcp snooping database 

B. show ip dhcp snooping binding 

C. show ip dhcp snooping statistics 

D. show ip dhcp pool 

E. show ip dhcp source binding 

F. show ip dhcp snooping 


Q37. Refer to the exhibit. 

What is the effect of the given command sequence? 

A. It configures IKE Phase 1. 

B. It configures a site-to-site VPN tunnel. 

C. It configures a crypto policy with a key size of 14400. 

D. It configures IPSec Phase 2. 


Q38. In what type of attack does an attacker virtually change a device's burned-in address in an attempt to circumvent access lists and mask the device's true identity? 

A. gratuitous ARP 

B. ARP poisoning 

C. IP spoofing 

D. MAC spoofing 


Q39. What is an advantage of placing an IPS on the inside of a network? 

A. It can provide higher throughput. 

B. It receives traffic that has already been filtered. 

C. It receives every inbound packet. 

D. It can provide greater security. 




Given the new additional connectivity requirements and the topology diagram, use ASDM to accomplish the required ASA configurations to meet the requirements. 

New additional connectivity requirements: 

. Currently, the ASA configurations only allow on the Inside and DMZ networks to access any hosts on the Outside. Your task is to use ASDM to configure the ASA to also allow any host only on the Outside to HTTP to the DMZ server. The hosts on the Outside will need to use the public IP address when HTTPing to the DMZ server. 

. Currently, hosts on the ASA higher security level interfaces are not able to ping any hosts on the lower security level interfaces. Your task in this simulation is to use ASDM to enable the ASA to dynamically allow the echo-reply responses back through the ASA. 

Once the correct ASA configurations have been configured: 

. You can test the connectivity to from the Outside PC browser. 

. You can test the pings to the Outside ( by opening the inside PC command prompt window. In this simulation, only testing pings to will work. 

To access ASDM, click the ASA icon in the topology diagram. 

To access the Firefox Browser on the Outside PC, click the Outside PC icon in the topology diagram. 

To access the Command prompt on the Inside PC, click the Inside PC icon in the topology diagram. 


After you make the configuration changes in ASDM, remember to click Apply to apply the configuration changes. 

Not all ASDM screens are enabled in this simulation, if some screen is not enabled, try to use different methods to configure the ASA to meet the requirements. 

In this simulation, some of the ASDM screens may not look and function exactly like the real ASDM. 

Answer: Follow the explanation part to get answer on this sim question.