Shortcuts To 352-001(91 to 100)

Actualtests offers free demo for 352-001 exam. “CCDE Written Exam”, also known as 352-001 exam, is a Cisco Certification. This set of posts, Passing the Cisco 352-001 exam, will help you answer those questions. The 352-001 Questions & Answers covers all the knowledge points of the real exam. 100% real Cisco 352-001 exams and revised by experts!

2017 NEW RECOMMEND

Free VCE & PDF File for Cisco 352-001 Real Exam
(Full Version!)

Pass on Your First TRY 100% Money Back Guarantee Realistic Practice Exam Questions

Free Instant Download NEW 352-001 Exam Dumps (PDF & VCE):
Available on:
http://www.certleader.com/352-001-dumps.html

Q91. Refer to the exhibit. 

An enterprise is migrating its single-area OSPF network from a Frame Relay WAN service to an MPLS L3VPN service. Frame Relay will remain in only a few sites that require increased resiliency via two different WAN connections. 

Which feature could be used in the ?MPLS VPN service provider network to support the design requirement by ensuring that during normal operation, intersite traffic will only use the MPLS VPN service and not the old Frame Relay service? 

A. virtual links 

B. sham links 

C. multiple stub areas 

D. super backbone 

Answer:

Q92. A service provider creates a network design that runs MPLS in its WAN backbone using OSPF as the IGP routing protocol. What would be two effects of additionally implementing MPLS-TE? (Choose two.) 

A. MPLS-TE is required to reroute traffic within less than 1 second in case of a link failure inside the backbone. 

B. MPLS-TE is required to route different MPLS QoS service classes through different paths. 

C. MPLS-TE and OSPF cannot be used together inside one MPLS network. 

D. MPLS-TE cannot use OSPF for the traffic path calculation. 

E. MPLS-TE is required to create backup paths independently from the IGP. 

Answer: B,E 

Q93. Refer to the exhibit. 

Company A is running a single-area OSPF, and Company B is running RIP as the IGP with no overlapping IP address spaces. Company A has just acquired Company B and both networks must be merged. Which three design components are recommended to guarantee connectivity and redundancy between the two networks? (Choose three.) 

A. Enable mutual redistribution between OSPF and RIP on one border router. 

B. Enable mutual redistribution between OSPF and RIP on Router A and Router B using route tags. 

C. Increase the administrative distance to 130 for the OSPF external prefixes on Router A and Router B. 

D. Implement an ACL on Router A and Router B to prevent OSPF external routes from being installed in the OSPF database. 

E. Filter external routes on Router A and Router B based on route tags. 

Answer: BCE 

Q94. You are designing a large Frame Relay WAN for a customer. The routing protocol is OSPF. What is the effect on the routing table if the WAN interfaces are configured as point-to-multipoint? 

A. Only a route for the DR will be present in the routing table. 

B. Configuring point-to-multipoint has no effect on the routing table. The route that is configured with the area command will be seen in the routing table. 

C. Multipoint interfaces dynamically add the network of the connected interface. 

D. Multipoint interfaces dynamically add a /32 route for each neighbor in the WAN. 

Answer:

Q95. Refer to the exhibit. 

Assume that no multicast optimization is done on LAN switches A and B. Which feature can be used to optimize multicast traffic forwarding in this situation? 

A. Enable IGMP snooping querier on both switches. 

B. Configure a static MAC entry for the multicast server. 

C. Disable IGMP snooping on both switches. 

D. Disable the IGMP query election process. 

E. Enable PIM Snooping on both switches. 

Answer:

Q96. You are designing a network for a branch office. In order to improve convergence time, you are required to use the BFD feature. Which four routing protocols can you use to facilitate this? (Choose four.) 

A. EIGRP 

B. IS-IS 

C. BGP 

D. static 

E. RIP 

Answer: ABCD 

Q97. You are asked to design a large campus network that will be using multicast for data transport. Which feature should be enabled at the Layer 2 access edge for host-only ports? 

A. PortFast 

B. BPDU guard 

C. PIM-SM 

D. PIM query interval 

Answer:

Q98. You are designing a NAC OOB Layer 3 Real-IP Gateway deployment for a customer. Which VLAN must be trunked back to the Clean Access Server from the access switch? 

A. untrusted VLAN 

B. user VLAN 

C. management VLAN 

D. authentication VLAN 

Answer:

Q99. Refer to the exhibit. 

How would you adjust the design to improve convergence on the network? 

A. Add an intra-POP link between routers 1A and 1B, and enable IP LFA FRR. 

B. Use an IP SLA between the end stations to detect path failures. 

C. Enable SSO-NSF on routers 1A and 1B. 

D. Use BGP to connect the sites over the WAN. 

Answer:

Q100. Which technique can you use to detect forwarding path failures at a uniform rate, and reconvergence times will be consistent and predictable when your routers are in the same broadcast domain? 

A. Enable BFD on your routers. 

B. Configure your routers with IP-SLA to ping the peer router. 

C. Configure your routers with IP-SLA and track to ping the peer and switch to a default route if the pings fail. 

D. Tune your routing protocol timers. 

Answer:

Certleader Dumps
Certleader is a company specialized on providing high quality IT exam materials and fully committed to assist our respected clients crack any IT certification tests on their 1st efforts.