Up to the minute Cisco 200-125 – An Overview 21 to 30

Exam Code: 200-125 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: CCNA Cisco Certified Network Associate CCNA (v3.0)
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass 200-125 Exam.

2016 Sep 200-125 Study Guide Questions:

Q21. – (Topic 9) 

What is the effect of the overload keyword in a static NAT translation configuration? 

A. It enables port address translation. 

B. It enables the use of a secondary pool of IP addresses when the first pool is depleted. 

C. It enables the inside interface to receive traffic. 

D. It enables the outside interface to forward traffic. 

Answer: A 

Q22. – (Topic 9) 

Which two features can dynamically assign IPv6 addresses? (Choose two.) 

A. IPv6 stateless autoconfiguration 



D. IPv6 stateful autoconfiguration 

E. ISATAP tunneling 

Answer: A,B 

Q23. – (Topic 4) 

If IP routing is enabled, which two commands set the gateway of last resort to the default gateway? (Choose two.) 

A. ip default-gateway 

B. ip route 

C. ip default-network 

D. ip default-route 

E. ip route 

Answer: C,E 

200-125  practice exam

Renovate 200-125 real exam:

Q24. – (Topic 4) 

Refer to the exhibit. 

What is the reason that the interface status is "administratively down, line protocol down"? 

A. There is no encapsulation type configured. 

B. There is a mismatch in encapsulation types. 

C. The interface is not receiving any keepalives. 

D. The interface has been configured with the shutdown command. 

E. The interface needs to be configured as a DTE device. 

F. The wrong type of cable is connected to the interface. 

Answer: D 

Q25. – (Topic 2) 

Refer to the exhibit. 

Which WAN protocol is being used? 



C. Frame Relay 


Answer: C 

Q26. – (Topic 9) 

Which three statements about link-state routing are true? (Choose three.) 

A. Routes are updated when a change in topology occurs. 

B. Updates are sent to a multicast address by default. 

C. OSPF is a link-state protocol. 

D. Updates are sent to a broadcast address. 

E. RIP is a link-state protocol. 

F. It uses split horizon. 

Answer: A,B,C 


Refined 200-125 dumps:

Q27. – (Topic 6) 

When you are troubleshooting an ACL issue on a router, which command would you use to verify which interfaces are affected by the ACL? 

A. show ip access-lists 

B. show access-lists 

C. show interface 

D. show ip interface 

E. list ip interface 

Answer: D 

Q28. – (Topic 4) 

A network administrator needs to allow only one Telnet connection to a router. For anyone viewing the configuration and issuing the show run command, the password for Telnet access should be encrypted. Which set of commands will accomplish this task? 

A. service password-encryption 

access-list 1 permit 

line vty 0 4 


password cisco 

access-class 1 

B. enable password secret 

line vty 0 


password cisco 

C. service password-encryption 

line vty 1 


password cisco 

D. service password-encryption 

line vty 0 4 


password cisco 

Answer: C 

Q29. – (Topic 2) 

What does a Layer 2 switch use to decide where to forward a received frame? 

A. source MAC address 

B. source IP address 

C. source switch port 

D. destination IP address 

E. destination port address 

F. destination MAC address 

Answer: F 

Q30. – (Topic 5) 

Which three features are added in SNMPv3 over SNMPv2? 

A. Message Integrity 

B. Compression 

C. Authentication 

D. Encryption 

E. Error Detection 

Answer: A,C,D 

About 200-125 Information: 200-125 Dumps