What Does 352-001 question Mean?

Master the 352-001 CCDE Written Exam content and be ready for exam day success quickly with this Actualtests 352-001 vce. We guarantee it!We make it a reality and give you real 352-001 questions in our Cisco 352-001 braindumps.Latest 100% VALID Cisco 352-001 Exam Questions Dumps at below page. You can use our Cisco 352-001 braindumps and pass your exam.

2017 NEW RECOMMEND

Free VCE & PDF File for Cisco 352-001 Real Exam
(Full Version!)

Pass on Your First TRY 100% Money Back Guarantee Realistic Practice Exam Questions

Free Instant Download NEW 352-001 Exam Dumps (PDF & VCE):
Available on:
http://www.certleader.com/352-001-dumps.html

Q81. Refer to the exhibit. 

Which two options provide the best loop protection in this topology, regardless of a bridged domain configuration? (Choose two.) 

A. PVRSTP on all switches 

B. REP on all switches 

C. MST on all switches 

D. BPDU guard on Switch A and Switch D 

E. 8032 on ring A-B-C-D 

Answer: BE 

Q82. An IBGP mesh design is being scoped, and in the discussions, one of the design engineers proposes the use of route reflectors. Which limitation is valid when using route reflectors in this design? 

A. The configuration complexity on the routers will be increased. 

B. Route reflectors will limit the total number of routes in the topology. 

C. Multipath information is difficult to propagate in a route reflector topology. 

D. Route reflectors will cause an opportunity to create routing loops. 

Answer:

Q83. Refer to the exhibit. 

You are designing a spanning-tree network for a small campus. Which two of these options would result in a trouble-free spanning-tree network design? (Choose two.) 

A. Convert all ports to trunk ports, prune off the VLANs that you do not require, and minimize the number of blocking ports. 

B. Introduce Layer 3 VLANs (SVIs) and prune off the VLANs that you do not require. 

C. Convert all the ports to trunk and enable BackboneFast. 

D. Convert all the ports to trunk and enable UplinkFast between all the links. 

Answer: AB 

Q84. What are two benefits of following a structured hierarchical and modular design? (Choose two.) 

A. Each component can be designed independently for its role. 

B. Each component can be managed independently based on its role. 

C. Each component can be funded by different organizations based on its role. 

D. Each component can support multiple roles based on the requirements. 

E. Each component can provide redundancy for applications and services. 

Answer: AB 

Q85. Tesla Radio GmbH is going to build a new research lab network based on a set of switches that would connect to their existing enterprise network. They are considering a design that would guarantee loop-free behavior within the set of switches. The design would also allow the group of switches to seem like a single switch to the enterprise network, because it is owned by a separate administrative group. Which Spanning Tree Protocol should be used to support the design requirements? 

A. IEEE 802.1w 

B. IEEE 802.1D 

C. IEEE 802.1s 

D. IEEE 802.1p 

Answer:

Q86. You are performing a BGP design review for a service provider that offers MPLS-based services to their end customers. The network is comprised of several PE routers that run iBGP with a pair of route reflectors for all BGP address families. Which two options about the use of Constrained Route Distribution for BGP/MPLS VPNs are true? (Choose two.) 

A. This feature must be enabled on all devices in the network at the same time. 

B. The RR must advertise the default route target filter toward the PE routers. 

C. The RRs do not need to advertise any route target filter toward the PE routers. 

D. Both PE and RR routers must support this feature. 

Answer: BD 

Q87. Refer to the exhibit. 

You are developing a migration plan to enable IPv6 in your IPv4 network. Starting at R3 and assuming default IS-IS operations, what is likely to happen when you enable IPv6 routing on the link from R3 to R2? 

A. Only R3 and R2 have IPv4 and IPv6 reachability. 

B. R2 receives an IPv6 default route from R3. 

C. Loopback reachability between all routers for IPv4 is lost. 

D. All routers except R2 are reachable through IPv4. 

E. R3 advertises the link from R3-R2 to R1, R4 and R5 only. 

Answer:

Q88. A company wants to connect two data center sites using a hub-and-spoke design with 2000 remote sites. One design consideration is the requirement to transfer MPLS packets over the public Internet. In addition, one router at each site should be used, and the MPLS packets must be encapsulated inside IP packets because the public Internet cannot transfer native MPLS packets. Which feature can be used to simplify the network design? 

A. GET VPN can be used to encrypt the MPLS packets with IPsec. 

B. DMVPN can be used to build up GRE tunnels dynamically with MPLS encapsulation inside. 

C. L2TPv3 can be used to encapsulate the MPLS packets. 

D. Site-to-site IPsec without GRE can be used to encapsulate the MPLS packets. 

E. PPPoE can be used to encapsulate the MPLS packets. 

Answer:

Q89. A multicast network is using bidirectional PIM. Which two actions, when combined, can achieve high availability so that two RPs within the same network can act in a redundant manner? (Choose two.) 

A. Use Anycast RP based on MSDP peering between the two RPs. 

B. Use a phantom RP address. 

C. Advertise routes for the two RPs with the same subnet mask through the unicast routing protocol. 

D. Advertise routes for the two RPs with different subnet mask lengths through the unicast routing protocol. 

E. Manipulate the administrative distance of the unicast routes to the two RPs. 

F. Manipulate the multicast routing table by creating static mroutes to the two RPs. 

Answer: BD 

Q90. In a large enterprise network with multiple data centers and thousands of access devices, OSPF is becoming unstable due to link flapping. The current design has the access devices multihomed to large aggregation routers at each of the data centers. How would you redesign the network to improve stability? 

A. Add a layer of regional Layer 3 aggregation devices, but leave the ABR function on the data center aggregation routers. 

B. Add a layer of regional Layer 2 aggregation devices, but leave the ABR function on the data center aggregation routers. 

C. Add a layer of regional Layer 3 aggregation devices and move the ABR function to the regional aggregation device. 

D. Add a layer of regional Layer 2 aggregation devices and move the ABR function to the regional aggregation device. 

Answer:

Certleader Dumps
Certleader is a company specialized on providing high quality IT exam materials and fully committed to assist our respected clients crack any IT certification tests on their 1st efforts.